Response: R_7VeFI1z44LiWyo8

URL to view Results

Response Summary:

A hot work permit is required for any temporary operation involving flames or the producing of heat and/or sparks. This includes, but is not limited to: brazing, cutting, grinding, soldering, thawing pipe, torch applied roofing, and welding.

Instructions:

Complete the checklist below indicating that all precautions have been considered and will be taken whenever possible.
Once complete, the permit request will be sent to EH&S and/or the Fire Marshal for review.
If the request is complete and precautions are satisfactory to the reviewer, you will receive an approved hot work permit via email within 24 hours. If this is a rush request, complete the request form then call EH&S Safety at 951-827-5118.

After receiving the approved permit, it must be posted at the job site until hot work activity has been completed. When the job is finished, fill in the "Work Completion Notice" section at the bottom of the approved permit and email to hotwork@ucr.edu. Keep a copy of the permit for your records.

Q2. PLEASE SELECT PERMIT TYPE:

Facilites maintenance and other small projects

Q3. PRECAUTIONS CHECKLIST:
Note: If necessary, please use the comments area below to further explain why a listed precaution cannot be taken in the manner described.

Available sprinklers, hose streams, and fire extinguishers are in service and operable
Hot work equipment is in good repair
Fire detection equipment protected from false activation
PPE is used to protect workers from physical and chemical hazards while hot work is being performed

Q4.

WITHIN 35 FEET (11 METERS) OF HOT WORK SITE:

Flammable liquids, dust, lint, and oily deposits are removed/cleaned
Explosive atmosphere in area is eliminated
Floors are swept and clean
Combustible floors are wet down and/or covered with fire protection blankets
Other combustibles are removed when possible or else covered with fire protection blankets or metal shields
All wall and floor openings are covered
Fire protection blankets are suspended beneath work
Ducts and conveyors that might carry sparks to distant combustible materials are protected or shut down

Q5. FIRE WATCH/HOT WORK AREA MONITORING:

Fire watch will be provided during and for at least 30 minutes after work stops
(including lunch and break times)
Fire watch is supplied with suitable fire extinguishers and fire fighting equipment
Fire watch is trained in the use of fire extinguishing equipment and in sounding emergency alarm
Additional fire watch may be required in adjoining areas, above, and/or below
Fire watch will verify isolated fire detection equipment is returned to normal operation

Q6. WORK ON WALLS, CEILINGS, AND/OR ROOFS:

Does not apply

Q7. WORK ON ENCLOSED EQUIPMENT:

, Enclosed equipment is cleaned of all combustibles
Containers have been purged of flammable liquids and vapors
Pressurized vessels, piping, and other equipment removed from service, isolated, and vented

Q8. OTHER PRECAUTIONS TAKEN:

N/A

Q9. OTHER COMMENTS:

N/A

PLEASE COMPLETE ALL FIELDS BELOW

Q11. HOT WORK BEING PERFORMED BY:

UC Riverside employee

Q12.

HOT WORK OPERATOR:

Name	Daniel Mendez
Company/Department	Sheet metal shop welding shop
Mobile Phone Number (###-###-####)	9512957963

Q14. FIRE WATCH:

Name	Laszlo Nemeth
Company/Department	Sheet metal shop/welding shop
Mobile Phone Number (###-###-####)	9512567287

Q15. JOB TIME FRAME:

Start date	02/04/2025
Start Time	6:00 AM
End Date	02/14/2025
End time	2:30 PM

Q16. LOCATION OF HOT WORK (BUILDING, FLOOR, ROOM, ETC.)

Piece hall basement

Q36. Project/WO Number:

59904

Q17. PROJECT/JOB DESCRIPTION:

Fabricate and welding catwalk

Q18. FACILITIES SUPERVISOR OR UCR PROJECT MANAGER SUPERVISING THIS JOB:

Name	Cory.gryniuk
Phone Number	9518277362
Email	Cory.gryniuk@ucr.edu

Q19. HOT WORK PERMIT REQUESTOR:

Name	Laszlo Nemeth
Department/Contractor Company	Sheet metal/Welding shop
Phone Number	9512567287
Email Address	Laszlo.nemeth@ucr.edul

Embedded Data:

N/A